Перейти до вмісту
FlySIPFlySIP Docs

Test the dialplan

Цей контент ще не доступний вашою мовою.

testDialplan simulates a call without placing it: it authenticates the call, finds the tariff and rate, and returns the routes the switch would try in order. It is the API behind Test Dialplan in the panel. Only customers with system management rights may call it.

The method supports trusted mode with i_customer.

You test one of two kinds of call:

  • Authenticated Call: a call already authenticated as an account. Send fallback_i_account and is_ivr_originated.
  • Not Authenticated Call: a call arriving from the network that the switch must authenticate first. Send remote_ip, i_protocol and the SIP domains.

Parameters

Section titled “Parameters”
Name Type Required Description
cld string yes Called number (CLD)
cli string no Calling number (CLI)
call_start_time string no Simulated start of the call (Call Start Date/Time) in UTC, in the form 09:57:29.000 GMT Mon May 29 2017
fallback_i_account int no Authenticated call: ID of the account the call is authenticated as (Authenticated as)
is_ivr_originated boolean no Authenticated call: True
remote_ip string no Not authenticated call: source IP address of the call (Remote Address)
remote_udp_port string no Not authenticated call: source port (the :Port part of Remote Address)
i_protocol int no Not authenticated call: signalling protocol (Protocol). IDs from the protocols dictionary
to_domain string no Not authenticated call: domain of the To header (To Domain)
from_domain string no Not authenticated call: domain of the From header (From Domain)
nated boolean no True: the caller is behind NAT (Caller is behind NAT)
pai_hdr string no Content of the P-Asserted-Identity header (P-Asserted-Identity)
rpid_hdr string no Content of the Remote-Party-ID header (Remote-Party-Id)

Returns

Section titled “Returns”
Name Type Description
result string OK when the call can be routed, Failure when it cannot
cause string With Failure: why the call fails, for example Invalid CLD length
cli, cld string The numbers after translation
lrn_cli, lrn_cld string The numbers after an LRN lookup, when the routing group uses LRN
i_account int Account the call was authenticated as
i_authentication int Authentication rule that matched
i_did, did int, string DID that matched, for a call to a DID
i_did_authorization int Authentication rule of the DID that matched
i_ivr_application int IVR application that answers the call
i_tariff, tariff_name int, string Tariff used to rate the call
i_rate, prefix int, string Rate and its prefix
price_1, price_n double Prices per minute of the rate
i_routing_group, routing_group_name int, string Routing group used
routes array Routes in the order they are tried. See the route fields
onnet_account struct For an on-net call to another account of the switch: i_account, username, i_did and routes with the same fields. routes at the top level is then not used

With cause set to Invalid CLD length the response also has dest_prefix and i_destination, the destination whose length limits failed, and min_length and max_length, each a number or None.

Route fields

Section titled “Route fields”
Name Description
cli, cld Numbers sent to this route, after the connection’s translation rules
prefix Matching prefix of the destination set
i_destination_set, destination_set_name Destination set of the route
i_route ID of the route
i_vendor, vendor_name Vendor
i_connection, connection_name Connection
system_connection The route goes to a system connection
i_media_relay Media relay used
capacity, num_sessions Channel limit of the connection and calls in progress on it
preference Preference of the route
quality_monitor_enabled, connection_quality, quality_monitor_action Quality monitoring of the connection: connection_quality is 1 when the quality is good; quality_monitor_action is block when bad quality blocks the connection
estimated_cost Estimated cost of the call through this route
free_seconds, connect_fee, grace_period, post_call_surcharge, interval_1, interval_N, price_1, price_N, area_name Billing parameters of the route
forbidden The route is forbidden and is not tried
onnet_route_type 1 listen to voicemail, 2 record voicemail, 3 on-net route, 7 service code, None vendor route
error Optional: why the route is skipped, for example loss_protection
error_cause Optional: explanation of error

Example

Section titled “Example”
request
call("testDialplan", {
    "cli": "15555550100",
    "cld": "442071234567",
    "fallback_i_account": 3092,
    "is_ivr_originated": True,
})
response
{
    "result": "OK",
    "cli": "15555550100",
    "cld": "442071234567",
    "i_account": 3092,
    "i_tariff": 12,
    "tariff_name": "Retail USD",
    "prefix": "4420",
    "price_1": 0.02,
    "price_n": 0.02,
    "i_routing_group": 14,
    "routing_group_name": "Wholesale LCR",
    "routes": [
        {
            "prefix": "4420",
            "i_destination_set": 118,
            "destination_set_name": "Carrier A - wholesale",
            "i_vendor": 12,
            "vendor_name": "Carrier A",
            "i_connection": 41,
            "connection_name": "Carrier A - SIP",
            "preference": 5,
            "estimated_cost": 0.012,
            "forbidden": False,
            "onnet_route_type": None,
            # … the other route fields
        },
    ],
}

Errors

Section titled “Errors”
faultCode Cause
407 A not authenticated call matched no authentication rule. Check remote_ip, the protocol and the domains
Section titled “Related”